Showing posts with label Jansjo. Show all posts
Showing posts with label Jansjo. Show all posts

Saturday, 8 February 2014

Jansjo flower lamp


Materials: Jansjo lamp and yogurt bottle

Description: Cut the yoghurt bottle into the right length to form the petals. Slice into strips and bend them over to the neck of the bottle. Stick the strips onto the neck of the bottle and secure with a zip tie.



Cut a hole in the bottle cap to allow the Jansjo lamp to go through. Place the lamp through the flower shade and you're done.

~ loic goulouzelle, Brest - France

Camping Jansjo battery powered light


Materials: Jansjo lamp, Li-ion battery, socket, wire

Description: I want to share with you a simple "invention" I made to have a camping Jansjo.

At home I have three lamps JANSJO–. They are powered by a switching power supply. The cable lamp is connected to the 4Vdc power supply by an old type speaker connector (in Italy we call it "Punto-linea" connector).

Within the head, close to the LED chip, the current is adjusted with a special IC (I have opened one head, but I do not remember: I think there are two 340mA regulators in parallel for a total of 680mA) and a voltage of 3.4 V is enough to obtain the maximum intensity.



Having some Lithium cylindrical 3.7V nominal (3 ~ 4.2V according to the actual state of charge) 2.4 Ah cells salvaged from old laptops battery packs (I also use that cells for the flashlight, etc., and charge them with a specific Li-ion charger Soshine SC-S1 V3) I thought it might be suitable for JANSJO.

So I connected a small piece of red and black wire to female speaker connector and the other two ends to a
cell, holding them by a slice of bicycle inner tube. (anyone who repair bicycles has some of them to give). The night between the 14th and the 15th of August we had four hours of great lighting at about no cost in the gazebo at the beach!

Ah ... I had also brought the gas lamp, but the light was ridiculous compared to a single JANSJO–! :-)

Have a good camping! :-)

~ Gianluca Giangreco, Roma, Italy

Monday, 17 December 2012

Bedtime Reading Lights


Materials: Hemma and Jansjo Lights

Description: The mattress is really thick so light from regular table lamps does not work. I broke the desk and standing lamps down to their bare components and rebuilt them in this configuration.



I had to extend the low voltage wires through the poles and mounted the switches on the headboard. I also bent the poles a little using a home made jig. Overall, a relatively easy afternoon project that functions effectively.

~ Robert Fontaine

Saturday, 23 June 2012

Adding light to Dave laptop desk


Materials: Dave laptop desk Jansjo light

Description: I have tried to add a light to the Dave desk, just have not been able to find one that clipped on right or sat on the top of the desk. I found the Jansjo light where the base was not attached to light entities, just screwed together well.

I threw away the weighted base. Drilled two holes in my Dave desk and screwed the light to that. Now I have light on my Dave desk that lights up my keyboard on my laptop.

~ Greg Baxter, Arizona

Wednesday, 6 June 2012

Tripod Desk Light


Materials: Jansjo Work Lamp

Description: As a gift for family, I wanted to make them a low-power desk/task light that was clean and simple, but also useful. After researching tons of LED options and looking at buying LEDs, drivers and power supplies it was a big relief to find Ikea's Jansjo light was a cheaper and more convenient option.

I carefully disassembled the light by prying off the lens, unscrewing the LED board from the aluminum holder and then cutting the power wires.



I used solid oak dowels from Home Depot. I went with 1" diameter for the body of the light since I knew that I would have to fit the entire LED board and make sure there was enough wood-material to support the legs below.

I drilled holes with forstner bits so that they would be clean and flat on the bottom and accommodate a snug fit for both the board and the legs.

For aesthetics and to reduce slipping, I used Plastidip on the bottoms of the dowels. I know they have tons of colors and you can even mix your own, but I think red really looks the best. It will match the wiring as well. It goes on really thick and thins out when it dries. I needed a second coat, but actually liked the way the first coat still showed a little wood grain through.

I soldered new wire leads on the LED boards using Radio Shack's "hook up" wire and red heat-shrink tubing. I then mounted the LED board to the dowel with a little Arctic Silver thermal glue. After testing and double-checking for polarity (LEDs won't work if you get the voltage reversed), I spliced those wires back into the black leads coming from the Jansjo's power switch.

I then cut small slits on either side of the LED opening and fit it with a circular lampshade made of vellum about 4" in diameter.

Tie them up with a ribbon and they're ready to be delivered!

~ Mark Fischer, Minneapolis

Saturday, 3 December 2011

Spotlight for roll-up displays


Materials: JANSJO� - Work lamp, silver-colour

Description: We wanted to illuminate with a spotlight 20 roll-up displays.
We bought some JANSJO� - Work Lamp at the IKEA store in Brescia. Instead of the base we mounted a connector designed by us and built with the rapid prototyping technique.


We think we're the only ones with the spotlights on the roll-up displays


~ Valerio Villa and Gabriele Baronio, University of Brescia

Monday, 29 August 2011

Bedside-Table-Cabinet-Lamp


Materials: JANSJ�, F�RH�JA

Description: The IKEA Bedside-Table-Cabinet. Amazing in itself, but somewhat lacking functionality when darkness falls.

What we do is take the IKEA JANSJ� worklamp, and combine it with the F�RH�JA wall cabinet to create the amazing Bedside-Table-Cabinet-Lamp.

1) Remove lamp from packaging
2) Measure out where to drill holes
3) Drill holes (this means using a 5mm drill bit, and widening the hole enough to get a snug fit - a 6mm drill bit made the hole too big, so beware!)
4) Insert lamp
5) Insert screws
6) Plug in lamp, and enjoy!


See more of the bedside table with light.

~ Samuel Caesar Hav, Danmark

Thursday, 3 February 2011

Jansjo lamp for computer monitor


Materials: Jansjo, drill, plus whatever monitor

Description: I love the Jansjo, but hate fumbling for the switch.

My ACER monitor has the base thick enough to hide the switch, so why not ?


The toggle switch is low voltage and very small; so I just drill a hole, run the wiring inside the base, mount the light and switch and re-solder it.

~ Dave Wong, New York

Tuesday, 1 February 2011

Convert LED Wall Light for use in RV


Materials: Jansjo

Description: I fell in love with the Jansjo LED wall light and I wanted to use it in my RV. It makes the perfect bedroom reading light, and since it's based on a light-emitting diode (LED) it's low power and you can't burn yourself by accidentally touching it.

Unfortunately, it doesn't run on a standard voltage. The special power adapter is built into the cord which plugs into the wall so there's no way to use it while camping or in a trailer. No problem.

In order to accomplish this hack you will need a Janslo lamp, a sub-miniature toggle switch ($3.00 from Radio Shack), a 1-watt LED power driver ($3.00 from Sure Electronics on eBay), and the ability to solder.

Cut the cord off the lamp and remove the little plastic screw that holds the cord in place. Unthread the power cord from the hole and clip off the white connectors, using care to leave the remaining wires as long as possible.

Drill out the hole that the cord went through using a 1/4" twist drill. Bend the contacts on the switch to be as flat as possible, slip the switch into the hole from the inside, and epoxy it in place. When the epoxy has set, you are ready to attach the cord and wire up the switch.


Solder the wires to the switch as shown using a piece of the old lamp cord. Polarity is very important with this project. You do not want to get the leads reversed. If you look carefully at the lamp cord, you will notice that one side of it is marked with little black dashes. Connect this side to the silver wire on the lamp. Connect the other side to the switch as shown. Connect the white wire from the lamp to the other side of the switch.

You are now ready to wire up the LED driver.

Strip a 1/4" of insulation off the wires to the lamp and attach them to the LED+ and LED- terminals on the driver board using the screw terminals. Once again, mind the polarity. The wire with the black dashes goes to the LED- terminal. The other one goes to LED+.

Attach the other side of the driver board to the 12-volt wires in your RV, being careful to observe the polarity. If you hook it up backwards, you will destroy the driver board (and possibly burn yourself).

That's it! You now have a very bright, very efficient reading light. It uses less than 1/10th the power of a standard 12-volt light bulb (150mA vs 2000mA).

~ Rick Scherle, San Francisco, CA